Combustion problem never fixed Okofen

[Christophe]

More seriously, according to Okofen boilers on a "cold" start, of all that I have already seen pass it can be from 6 to sometimes 14 minutes to find yourself at 100% combustion.
My own average being closer to 8/9 minutes.

In your case, is it a cold cold or semi-cold fireplace?

[Pilpoill]

Hi,

Concerning Fontcouverte, the average of its cycles is 27 min and even considering the current settings made by O apart from trying to increase them in an astonishing way...
Its flame temperature and depression instructions are respected, so I don't see anything on that side.

software setting (the same hardware base is often 10/18kW or 22/32kW)
Eight of them were perfectly chosen and adapted.
Four were clearly oversized, cycle times between 20 and 30 minutes

If a 27 min cycle is normal and the power can be adapted by software adjustment, where is the problem?

I was only pointing out the inconsistency of the statement: 20 to 30 minutes is normal but not 27 minutes

Hello,

I note that its average cycles are 27 minutes, then that its flame and depression temperature values ​​are consistent and finally I emphasize that four boilers were clearly OVERsized with an average time of 20 to 30 minutes.

Where did I write that cycles of 20, 27 or 30 minutes could be considered normal?

[izentrop]

Ok, I asked the wrong question. In fact I wanted to know what was the normal length of a cycle. Did 67 was talking about 75 minutes.
I know that a pellet stove can modulate its flame power, so I guess for a boiler we should be able to maintain the cycle even for several hours if the outside temperature is low and a low water circuit temperature. Maximum yield in this case.

[Bernard01290]

Hello,

The reference of the suction cup outlet is as follows:
Vertical BIOTEN kit diam 130 / 200.

At home Okofen updated the software to the latest version... he said on February 1, to no effect.
Have a good day

[izentrop]

In an Okofen note https://www.professionplombier.fr/asset ... 5-2021.pdf, for a 15° roof, the smoke outlet should be at least 60 cm.
In that case or or the pipe is less than 1 m from the neighboring roof, it would be necessary to add the height of the bottom of this roof to avoid at least blackening the gutter and sending smoke inside, it seems to me -he

[Christophe]

Thanks Izy for the research: that was what I was referring to above…vis à vis the ridge for classic ducts!

Conclusion: professionals don't know the basics of their job…and it's ugly!

[Pilpoill]

Hello,

The reference of the suction cup outlet is as follows:
Vertical BIOTEN kit diam 130 / 200.

At home Okofen updated the software to the latest version... he said on February 1, to no effect.
Have a good day

Hello,

I just called the Seten company, the person who answered me after seeing the two photos of your identical outputs told me that it was not their product

And in their catalog, there is actually nothing similar https://www.seten.com/wp-content/upload ... 2022-1.pdf


Bernard01290, what is the power of your Compact as well as the average duration of its cycles?

[Bernard01290]

Hello,

BIOTEN is the reference I found on the estimate. Pictured what I saw on the boiler outlet pipe.

For the exit to the roof, the photo is taken from the ground. The air intake is about a meter above the roof.
I can take a more specific photo if needed.
Have a good day

download / file.php? mode = view & id = 28284

[Bernard01290]

Power 22 kW.

How to find the duration of the cycles?
Thank you

[Pilpoill]

Power 22 kW.

How to find the duration of the cycles?
Thank you

In principle, while walking through the menus, there are two possibilities:
- Pellematic / Compact
- Or directly via the Measurements menu

In the long list on the right, there will be this:

AC98D619-2666-42B1-9E90-246F13AF61E5.jpeg (39.31 Kio) Consulté 1330 fois