Need help connecting a programmer EG071

Hi-tech electronic and computer equipment and Internet. Better use of electricity, help with the work and specifications, equipment selection. Presentations fixtures and plans. Waves and electromagnetic pollution.
New topic Reply
User avatar
elephant
Econologue expert
Econologue expert
posts: 6646
Registration: 28/07/06, 21:25
Location: Charleroi, center of the world ....
x 7




by elephant » 31/12/12, 11:04

The diagram seems correct to me.

2 things to check:

does the load work "as is"?
is there voltage at the terminals of the load in "on" mode

it is not impossible that a contact gives O ohm to the test, but that it does not support the load (but in this case, often we hear it sizzling)

try to put a light bulb in place of the load, to see.
0 x
elephant Supreme Honorary éconologue PCQ ..... I'm too cautious, not rich enough and too lazy to really save the CO2! http://www.caroloo.be
Skin
User avatar
fabio.gel
Éconologue good!
Éconologue good!
posts: 282
Registration: 06/03/08, 13:33
Location: 14 - Calvados
x 6

Thank you to all




by fabio.gel » 31/12/12, 11:58

Ok that's good it works with a lamp.

It only remains for me to find a power contactor to put the programmer and the resistance.
0 x
I do my best to not leave trash world to my children ....
Skin
User avatar
moulino51
I understand econologic
I understand econologic
posts: 85
Registration: 27/02/12, 01:50
Location: On land near Reims
x 3

Re: Thank you all




by moulino51 » 31/12/12, 13:13

fabio.gel wrote:I just have to find a power contactor


I still have some in stock, if you can't find them at home (in Hager and Legrand which I don't use)


GS
0 x
Skin
User avatar
fabio.gel
Éconologue good!
Éconologue good!
posts: 282
Registration: 06/03/08, 13:33
Location: 14 - Calvados
x 6

Re: Thank you all




by fabio.gel » 31/12/12, 13:45

moulino51 wrote:
fabio.gel wrote:I just have to find a power contactor


I still have some in stock, if you can't find them at home (in Hager and Legrand which I don't use)


GS


I answered you by mp

Thank you
0 x
I do my best to not leave trash world to my children ....
Skin
User avatar
moulino51
I understand econologic
I understand econologic
posts: 85
Registration: 27/02/12, 01:50
Location: On land near Reims
x 3

Re: Thank you all




by moulino51 » 31/12/12, 14:37

fabio.gel wrote:I answered you by mp


You also have a MP in the box 8)



GS
0 x
Skin
Alain G
Econologue expert
Econologue expert
posts: 3044
Registration: 03/10/08, 04:24
x 3




by Alain G » 31/12/12, 18:42

Well, I can see that things are taking place with the help of Moulino, so Fabio will be able to finish the assembly and of course understand the relatively basic operation for the initiated!

: Mrgreen:
0 x
Stepping behind sometimes can strengthen friendship.
Criticism is good if added to some compliments.
Alain
Skin
User avatar
fabio.gel
Éconologue good!
Éconologue good!
posts: 282
Registration: 06/03/08, 13:33
Location: 14 - Calvados
x 6

Unity is strength




by fabio.gel » 31/12/12, 19:17

Alain G wrote:Well, I can see that things are taking place with the help of Moulino, so Fabio will be able to finish the assembly and of course understand the relatively basic operation for the initiated!

: Mrgreen:


Yes alain

I would go to bed less this evening : Cheesy:
0 x
I do my best to not leave trash world to my children ....
Skin
boulouloubi
I discovered econologic
I discovered econologic
posts: 3
Registration: 08/01/13, 08:37
Location: Mauritius




by boulouloubi » 13/01/13, 15:11

Hello everyone with the same creature at home, I take this opportunity for you to give me your lights, I just have to connect two lamps in 12V of 50W, on my electrical board are that I must precede it with a breaker of 10A? Would the connection be the same as presented by alain? I wanted to impress madam, but I already programmed the gadget and that was enough for me : Mrgreen:
thank you in advance for your help
0 x
Skin
Alain G
Econologue expert
Econologue expert
posts: 3044
Registration: 03/10/08, 04:24
x 3




by Alain G » 14/01/13, 16:31

boulouloubi wrote:Hello everyone with the same creature at home, I take this opportunity for you to give me your lights, I just have to connect two lamps in 12V of 50W, on my electrical board are that I must precede it with a breaker of 10A? Would the connection be the same as presented by alain? I wanted to impress madam, but I already programmed the gadget and that was enough for me : Mrgreen:
thank you in advance for your help


Welcome to Éconologie boulouloubi!

I assume you have a transformer to power your lamps at 12 volts?


If yes you can use this scheme:

Image


You connect the input of the transformer to the output "use to electrical device" and the output of the transformer directly to your lights.

Input fuses of 5 or 10 amps should be provided at the input of the timer,
:D
0 x
Stepping behind sometimes can strengthen friendship.

Criticism is good if added to some compliments.

Alain
Skin
boulouloubi
I discovered econologic
I discovered econologic
posts: 3
Registration: 08/01/13, 08:37
Location: Mauritius




by boulouloubi » 14/01/13, 16:56

Hello everyone, I have indeed two transformers, and thank you alain for your welcome and your very clear and quick answer, but are I in need of a power contactor even for my two unfortunate 50W spot? This programmer is terrible in addition he must be accompanied before and also after : Cry:I had not planned as many people in my little box .....

respect for those who read the instructions and program the gadget in less than an hour : Mrgreen:must be in good shape : Shock:
0 x
Skin
 


  • Similar topics
    Replies
    views
    Last message
New topic Reply

Back to "Electricity, electronics and computers: Hi-tech, Internet, DIY, lighting, materials, and new"

Who is online ?

Users browsing this forum : No registered users and 111 guests