Raah, I have my slap, it's made the Nieme inflatable mattress that I use as an extra mattress (inside I specify) and which only takes 2 or 3 uses before having a leak ...
On one, I tried a bike patch but the polymerization is not done correctly (see not at all, normal it is the same material as an inner tube) ... so if the leak is reduced, it is still there...
Short: would anyone know of a reliable method of repairing this kind of mattress (PVC)?
Inflatable mattress 1 or 2 places with or without "velor" coating on one side, material not sure but a priori it would be PVC, usable in water for some ...
ps: on the decatlhon site I found it at 3 € but it seems a little light right?
Uh if it's just PVC glue: PVC pipe glue (pressure, evacuation ...) that stings the nose with its solvents (+ or - strong depending on the brand) wouldn't it work?
reps: a priori these mattresses were not used for sexual performance .... (well, I don't think so ...) ...
Repair leaking PVC inflatable mattress (shit in China)
-
- Moderator
- posts: 79364
- Registration: 10/02/03, 14:06
- Location: Greenhouse planet
- x 11060
Repair leaking PVC inflatable mattress (shit in China)
Last edited by Christophe the 09 / 03 / 11, 11: 22, 2 edited once.
0 x
Do a image search or an text search - Netiquette of forum
-
- Econologue expert
- posts: 2183
- Registration: 07/11/06, 13:18
- x 124
In general they start to flee at the welds. And there it is dead. Otherwise the patch glued to the pipe glue does it ... Neoprene too ... But it always ends up taking off again ...
I prefer to sleep on top and even on the clay or the grass I have not burst ...
http://www.decathlon.fr/matelas-gonflab ... 29334.html
I prefer to sleep on top and even on the clay or the grass I have not burst ...
http://www.decathlon.fr/matelas-gonflab ... 29334.html
0 x
I have never been able to reliably repair this type of mattress.
It must be said that they are practical, comfortable and space-saving.
If we had to do them with the same technique as the old ones, they would weigh heavy and occupy at least 3 times the volume they have.
Concerning the glue of swimming pools, I never tried on a mattress but it is a good idea because on a swimming pool I tried it and even a leak at the level of a weld it held a little, it was necessary to put back some time in time because under pressure the adhesive expands and the weld continues to cut.
It must be said that they are practical, comfortable and space-saving.
If we had to do them with the same technique as the old ones, they would weigh heavy and occupy at least 3 times the volume they have.
Concerning the glue of swimming pools, I never tried on a mattress but it is a good idea because on a swimming pool I tried it and even a leak at the level of a weld it held a little, it was necessary to put back some time in time because under pressure the adhesive expands and the weld continues to cut.
0 x
-
- Moderator
- posts: 79364
- Registration: 10/02/03, 14:06
- Location: Greenhouse planet
- x 11060
Ok thank you for the feedback ... so that's what I feared: it's not won !!
To start, I will try the patch solution + PVC glue ... because I have the gear on hand.
To start, I will try the patch solution + PVC glue ... because I have the gear on hand.
0 x
Do a image search or an text search - Netiquette of forum
-
- Moderator
- posts: 79364
- Registration: 10/02/03, 14:06
- Location: Greenhouse planet
- x 11060
Uh that's what I thought ... I have to sacrifice one of the other mattresses then?
0 x
Do a image search or an text search - Netiquette of forum
-
- Econologue expert
- posts: 2183
- Registration: 07/11/06, 13:18
- x 124
Christophe, you should make a thread on your "Merde in China", it is necessary. We buy Chinese because it is the cheapest but we would also like it to be of quality ....
If we make a normal mattress, made by people who are paid normally, we end up with a product that has become "luxury", with a very high price, for the rich. And what do righteous people say? They say it's theft and that these products shouldn't exist, we don't want them .... You should know.
Example: Are 600 € shoes theft?
ML
If we make a normal mattress, made by people who are paid normally, we end up with a product that has become "luxury", with a very high price, for the rich. And what do righteous people say? They say it's theft and that these products shouldn't exist, we don't want them .... You should know.
Example: Are 600 € shoes theft?
ML
0 x
-
- Similar topics
- Replies
- views
- Last message
-
- 12 Replies
- 10435 views
-
Last message by GuyGadeboisTheBack
View the latest post
19/06/23, 23:00A subject posted in the forum : Failure, troubleshooting and repair: repair yourself?
-
- 0 Replies
- 12683 views
-
Last message by Christophe
View the latest post
15/03/19, 12:12A subject posted in the forum : Failure, troubleshooting and repair: repair yourself?
-
- 3 Replies
- 3977 views
-
Last message by Christophe
View the latest post
21/02/16, 20:48A subject posted in the forum : Failure, troubleshooting and repair: repair yourself?
-
- 92 Replies
- 106142 views
-
Last message by izentrop
View the latest post
25/04/22, 11:17A subject posted in the forum : Failure, troubleshooting and repair: repair yourself?
-
- 25 Replies
- 63794 views
-
Last message by martine45
View the latest post
25/04/16, 11:26A subject posted in the forum : Failure, troubleshooting and repair: repair yourself?
Back to "failure, troubleshooting and repair: repair yourself? "
Who is online ?
Users browsing this forum : No registered users and 96 guests