Idea of ​​new type of bubbler

Water injection in thermal engines and the famous "pantone engine". General informations. Press clippings and videos. Understanding and scientific explanations on the injection of water into engines: ideas for assemblies, studies, physico-chemical analyzes.
ange
I learn econologic
I learn econologic
posts: 34
Registration: 12/10/05, 14:55




by ange » 19/10/05, 10:02

Hello,
There may be a way to replace the bubbler with a system like this!


http://www.basilic.ru/index.php?op=cat&sec=4&gn=243

The description in Russian does not matter. This is description of the inhaler which allows you to inhale all kinds of liquids, oils, etc.

Advantage is that the bubbler thus built can be very very compact !!!
:D
0 x
breizh
I discovered econologic
I discovered econologic
posts: 7
Registration: 04/10/05, 20:43




by breizh » 19/10/05, 11:36

spasibo.
0 x
Christophe
Moderator
Moderator
posts: 79113
Registration: 10/02/03, 14:06
Location: Greenhouse planet
x 10972




by Christophe » 19/10/05, 11:47

no chance of putting glass on an engine mount ... the vibrations would destroy it quickly ...
0 x
fclergue
I discovered econologic
I discovered econologic
posts: 6
Registration: 19/10/05, 11:33




by fclergue » 19/10/05, 11:48

Do you put it or your tank?
The outlet is at the top, the air intake at the bottom.
And when is there more liquid?

See you
François
0 x
ange
I learn econologic
I learn econologic
posts: 34
Registration: 12/10/05, 14:55




by ange » 19/10/05, 12:16

I showed you the operating principle of bubbler which can be made of stainless steel, eg
The fluid level is usually ~ 3-4 cm below. Nothing prevents having a second tank to permanently supply the bubbler.
:D
0 x
Thibounet
I learn econologic
I learn econologic
posts: 14
Registration: 30/03/05, 09:27
Location: Waterloo .be (Belgium)




by Thibounet » 02/11/05, 11:03

How does it work? : Rolleyes:
0 x
http://www.pagethib.be.tf Adapting a gas burner or oil to PMC
ange
I learn econologic
I learn econologic
posts: 34
Registration: 12/10/05, 14:55




by ange » 02/11/05, 14:51

It is originally a patented inhaler.
Bubbler used in the vertical position. It is filled 1/5 up to obstacle levels.

The operating principle is simple:
As the diameter of the passage increases, the gas loses its speed when passing through the liquid and produces bubbles. Obstacles inside the tube prevent suction of the liquid and stabilize its level.
This bubbler needs an external system to top up the liquid.

Some thoughts on improving the system:
Installation of a sieve or an obstructed passage with small orifices ~ 1-3 mm certainly improve the quality of the bubbles.
External tank using principles of communicating vessels perfectly ensured the supply of water or any other liquid.
0 x
rpsantina
I understand econologic
I understand econologic
posts: 175
Registration: 17/12/04, 16:11
Location: 81 - South Tarn
x 10




by rpsantina » 02/11/05, 21:49

It basically looks like a carburetor emulsion well with its tank ...

no ?? : Unsure:
0 x
RPS (Dpt Tarn South 81)
i-Only those who do nothing are never wrong
ii-Anything is possible as long as a little time is spent there
ange
I learn econologic
I learn econologic
posts: 34
Registration: 12/10/05, 14:55




by ange » 03/11/05, 14:33

Yes it can, except that instead of holes there are bubbles which act as obstacles. But you're right the well emulsion its very much like the bubbler :D
0 x

 


  • Similar topics
    Replies
    views
    Last message

Go back to "Water injection in heat engines: information and explanations"

Who is online ?

Users browsing this forum : No registered users and 121 guests