How to test a machine Leroy Somer DC LSC 132 J

Hi-tech electronic and computer equipment and Internet. Better use of electricity, help with the work and specifications, equipment selection. Presentations fixtures and plans. Waves and electromagnetic pollution.
New topic Reply
User avatar
chatelot16
Econologue expert
Econologue expert
posts: 6960
Registration: 11/11/07, 17:33
Location: Angouleme
x 264




by chatelot16 » 10/08/10, 22:06

your charger is useless: it will work the same without him

of course there is a diode bridge which prevents the return of current, but nothing says that this bridge supports 220v: in normal operation it has only a few ten volts to hold ...
0 x
Skin
Alain G
Econologue expert
Econologue expert
posts: 3044
Registration: 03/10/08, 04:24
x 3




by Alain G » 10/08/10, 22:37

chatelot16 wrote:your charger is useless: it will work the same without him

of course there is a diode bridge which prevents the return of current, but nothing says that this bridge supports 220v: in normal operation it has only a few ten volts to hold ...



The charger only serves to initiate the excitation after a rheostat must be installed to adjust the voltage to the desired use!

For a 40-volt diode bridge, the inversion voltage is 10 times higher, therefore 400 volts.

PrimoDVD

What do you intend to power with this generator because you will have to convert it into an alternative?
0 x
Stepping behind sometimes can strengthen friendship.
Criticism is good if added to some compliments.
Alain
Skin
User avatar
chatelot16
Econologue expert
Econologue expert
posts: 6960
Registration: 11/11/07, 17:33
Location: Angouleme
x 264




by chatelot16 » 10/08/10, 23:10

the macine with direct current starts very easily at the first foutieme of volt ... the battery charger was only a means of measurement in separate excitation, really separate .. it is absolutely useless once the good connection is found!

and I hear that there is no guarantee that a normal 12v charger will hold 230v

if it held once without grilling so much the better for you but do not start again for nothing it will not necessarily hold all the shots
0 x
Skin
dedeleco
Econologue expert
Econologue expert
posts: 9211
Registration: 16/01/10, 01:19
x 10




by dedeleco » 11/08/10, 00:23

Breathtaking, primodvd, always also in shoe polish !!
on the photo of wires to cross, there is no charger !!!


Amazing to go put the charger at 12V on it !!!
We never put 180V or 220V on 12V !!!

The 12V in general is found shriveled and burnt !!!
Basic knowledge !!!
Except strong luck !!!!
0 x
Skin
PrimoDVD
I learn econologic
I learn econologic
posts: 28
Registration: 01/08/10, 10:11




by PrimoDVD » 11/08/10, 10:44

in fact I had synthesized all the advice received ... the charger was to create an excitement and I did not think that I was going to reach 180V
Now that I know the correct connection I no longer need the charger
a macine in direct current starts very easily at the first foutieme of volt ... the battery charger was only a means of measurement in separate excitation, really separate .. it is absolutely useless once the good connection is found!
0 x
Skin
PrimoDVD
I learn econologic
I learn econologic
posts: 28
Registration: 01/08/10, 10:11




by PrimoDVD » 11/08/10, 11:19

alain ga wrote
What do you intend to power with this generator because you will have to convert it into an alternative?

for now I intend to install lighting in a barn ...
I was given this generator now remains to know how to run it
with wind or hydro or both
as for the conversion to AC it will be with a converter
0 x
Skin
 


  • Similar topics
    Replies
    views
    Last message
New topic Reply

Back to "Electricity, electronics and computers: Hi-tech, Internet, DIY, lighting, materials, and new"

Who is online ?

Users browsing this forum : No registered users and 259 guests