Search found 891 results

View gildas
08/11/10, 14:31
Forum : Water injection in engines: montages and experiments
Subject : Doping an internal combustion engine with water vapor
answers: 1290
views: 616349

You will say that I am annoying but that would not happen if the vapor would arrive above the butterfly! It would be necessary to act on the carb jets (or richness screw?) to have a balanced air-gasoline-steam mixture. (difficult to do?) This mixture would be balanced at all speeds. (Sa...
View gildas
06/11/10, 16:30
Forum : Water injection in engines: montages and experiments
Subject : Doping an internal combustion engine with water vapor
answers: 1290
views: 616349

No turbo on the Chevrolet petrol car, moreover my inlet is under the throttle valve so huge depression at idle and at low speed. You will say that I am annoying but that would not happen if the vapor would arrive above the butterfly! It would be necessary to act on the carb jets (or screw...
View gildas
05/11/10, 05:42
Forum : Water injection in engines: montages and experiments
Subject : Doping an internal combustion engine with water vapor
answers: 1290
views: 616349

Some cars check the engine temperature before opening the EGR valve, don't you know if this is a general case? In any case, or after 4 or 5 km it should work as hot. Well, the ideal would be to find this kind of car and see how fast the EGR valve gets dirty...
View gildas
04/11/10, 06:37
Forum : Water injection in engines: montages and experiments
Subject : Doping an internal combustion engine with water vapor
answers: 1290
views: 616349

The EGR valve is closed at idle (but there are exceptions) and especially at heavy loads (full throttle). Which would mean that it is open even for the first kms of a cold start...so clogging. The problem is that you will have a very long connection pipe....with...
View gildas
03/11/10, 11:13
Forum : Water injection in engines: montages and experiments
Subject : Doping an internal combustion engine with water vapor
answers: 1290
views: 616349

More seriously, the rag test is done on an identical course of about 20km, and at approximately the same speeds. The dimensions of the fabrics (cotton only) cut in the same piece must be approximately 40x40cm for small displacements, in order to allow a perfect seal...
View gildas
27/10/10, 21:12
Forum : Water injection in engines: montages and experiments
Subject : Doping an internal combustion engine with water vapor
answers: 1290
views: 616349

doping with water vapor

Good evening, It was while reading the composition of a medicine that I found an interesting component of antifreeze: propylene glycol http://fr.wikipedia.org/wiki/Propyl%C3%A8ne_glycol because it is much less harmful than propylene glycol. ethylene glycol. Interesting to put in the water of a bubbler because boiling point very ...
View gildas
27/10/10, 15:53
Forum : Heating, insulation, ventilation, VMC, cooling ...
Subject : Improved Oil Burner-reduction NOx and CO-Blue Flame
answers: 624
views: 637693

OOHH man of little faith! I would still point out to you that my old oil burner is now less polluting than the best GAS boilers, not bad, isn't it? The purpose of the maneuver was to demonstrate the effectiveness of water vapor within the combustion chamber, whether it is: - recycled and from...
View gildas
17/10/10, 14:38
Forum : Water injection in engines: montages and experiments
Subject : water doping test Audi 80 1.6 TD theoretical stage
answers: 19
views: 13878

Hello space, ok, I still have it for a moment partly theoretical ^^ there is a section on the forum where are the different assemblies displayed? https://www.econologie.com/plan-et-conseils-pour-un-dopage-al-eau-gillier-pantone-sur-motor-diesel-articles-3727.html There is also the search engine. ...

Go Advanced search