Search found 164 results
- 12/02/24, 22:04
- Forum : Heating, insulation, ventilation, VMC, cooling ...
- Subject : Okofen Pellematic for beginners..
- answers: 1
- views: 1216
Re: Okofen Pellematic for beginners..
Hello, I have an OKOFEN Pellematic boiler (with touch screen) and I cannot adjust it correctly. whether I put it in comfort or in auto it is always too cold. This morning it was 16.5 in the house for an outside temperature of 5°. Well, I'm just starting out and I have...
- 17/12/23, 15:39
- Forum : Heating, insulation, ventilation, VMC, cooling ...
- Subject : EasyPell V2 boiler with Easytouch FA V4.00 regulation
- answers: 6
- views: 1681
Re: EasyPell V2 boiler with Easytouch FA V4.00 regulation
To all readers, be careful what you do with these reserved menus…
Bad handling and everything will potentially be found if the warranty is at stake
Bad handling and everything will potentially be found if the warranty is at stake
- 15/12/23, 17:08
- Forum : Heating, insulation, ventilation, VMC, cooling ...
- Subject : Getting started with Okofen boiler and installation
- answers: 11
- views: 2255
Re: Getting started with Okofen boiler and installation
On recent versions, the graph submenu is in the measurements menu. It's up to you to select the curves you want to see. Whether or not you have a room thermostat, the line must appear in the curves to be displayed, even if it will not indicate any value on the daily graph.
- 15/12/23, 07:35
- Forum : Heating, insulation, ventilation, VMC, cooling ...
- Subject : Getting started with Okofen boiler and installation
- answers: 11
- views: 2255
Re: Getting started with Okofen boiler and installation
If you really want to invest in a thermometer, without wanting to advertise I recommend the ThermoPro TP358.
Otherwise from your boiler you go to measurements/graph and you check the curves like this:
Otherwise from your boiler you go to measurements/graph and you check the curves like this:
- 15/12/23, 05:16
- Forum : Heating, insulation, ventilation, VMC, cooling ...
- Subject : Getting started with Okofen boiler and installation
- answers: 11
- views: 2255
Re: Getting started with Okofen boiler and installation
Okay so it was a simple display bug because with 5°C outside, a request for 20°C in setpoint and with a 0,3/23 curve we obtain 26°C in flow temperature which is much more consistent with your observation of 25,5°C 8) The ethernet connector is located just on the back of the card just in case. All...
- 14/12/23, 19:39
- Forum : Heating, insulation, ventilation, VMC, cooling ...
- Subject : Getting started with Okofen boiler and installation
- answers: 11
- views: 2255
Re: Getting started with Okofen boiler and installation
At the moment, with an outside temperature of 5 degrees: - my heated floor has an ambient setting of 20, slope of 3 and foot of 23 => departure temp 25,5 and the atmosphere in the house is around 20 - my radiators upstairs have an ambient setting of 20, slope 0,6 and foot 25,5 =...
- 14/12/23, 19:08
- Forum : Heating, insulation, ventilation, VMC, cooling ...
- Subject : Getting started with Okofen boiler and installation
- answers: 11
- views: 2255
Re: Getting started with Okofen boiler and installation
Sit down, thus adjusted your heating curve gives a departure temperature of 72°C for a setpoint of 21°C if it is 0°C outside. You understand that there is a huge problem with this setting and if the work has been done according to the rules of the art for the PC there is a limit that must not be exceeded...
- 14/12/23, 12:37
- Forum : Heating, insulation, ventilation, VMC, cooling ...
- Subject : Getting started with Okofen boiler and installation
- answers: 11
- views: 2255
Re: Okofen boiler handling and installation
Hello, in 2014 was it a regulation with a screen like this?
For the slope of 3, the maximum that I have already had to follow is 1,6 with a foot of 44°
3 makes me think more of a setting to heat… a swimming pool which requires maximum calories.
For the slope of 3, the maximum that I have already had to follow is 1,6 with a foot of 44°
3 makes me think more of a setting to heat… a swimming pool which requires maximum calories.
- 14/12/23, 12:31
- Forum : Heating, insulation, ventilation, VMC, cooling ...
- Subject : OKOFEN pellematic settings
- answers: 10
- views: 3288
Re: OKOFEN pellematic settings
Did you freeze to death or were you cooked over low heat?
- 11/12/23, 17:21
- Forum : Heating, insulation, ventilation, VMC, cooling ...
- Subject : OKOFEN pellematic settings
- answers: 10
- views: 3288
Re: OKOFEN pellematic settings
If your network is made up of radiators, arrange the circulator this way when it is operating:
For the ECS it should be like this:
If you want me to look at the rest, send me your password by private message.
For the ECS it should be like this:
If you want me to look at the rest, send me your password by private message.