Search found 10 results

by Retroloc
02/12/04, 10:29
Forum : Water injection in engines: montages and experiments
Subject : Water doping plan Beetle
answers: 51
views: 70899

http://songe.is.free.fr/pmc/Moteur3.jpg moi ce que je vois sur l'image c'est qu'un carbu alimente le réacteur en étant alimenté à l'essence pure et que tout ça va en aval du carbu d'origine. Conclusion, même si ton réacteur est un perlinpinpin, même si c'est un tube creux, ça marchera quand même. (...
by Retroloc
30/11/04, 18:16
Forum : Water injection in engines: montages and experiments
Subject : Citroën 2CV 602cm3 possible?
answers: 36
views: 39917

Water and gasoline are not miscible, either! But water and ethanol yes and ethanol and gasoline as well. Conclusion, a little methylated spirits in a water / gasoline mixture and the whole becomes stable. As methylated spirit does not cost more than gasoline (1.04 € the last time) at ...
by Retroloc
30/11/04, 18:04
Forum : Water injection in engines: montages and experiments
Subject : Pantone engine in the Greater West and Brittany Region
answers: 31
views: 47481

erikotiti wrote:Pantone. In any case the difference in pollution is clear in favor of the Pantone engine.

NUMBERS ! Please...
by Retroloc
26/11/04, 12:49
Forum : Water injection in engines: montages and experiments
Subject : Water doping plan Beetle
answers: 51
views: 70899

[Here is the montage of Christophe (Kriss) http://songe.is.free.fr/pmc/Moteur1.jpg but there if I understand correctly the image you bring the output of the reactor UPSTREAM of the carburetor. So if the original gasoline system is not removed you pass the GEET gases through the venturis of the carburettor and you charge them ...
by Retroloc
26/11/04, 12:37
Forum : Water injection in engines: montages and experiments
Subject : Water doping plan Beetle
answers: 51
views: 70899

I do not see well on your assembly if you bring air between the reactor outlet and the inlet. If not, I imagine you run the reactor through combustion air. Is there a downside to this? I mean is the air going to cool the system, is it going to get "burst" in ...
by Retroloc
26/11/04, 12:25
Forum : Water injection in heat engines: information and explanations
Subject : Performing a test bench
answers: 32
views: 28707

In addition, it is recommended to have a rod and an interior surface as smooth as possible, it is perhaps not for nothing ... according to some it would be to facilitate the transition to the state of plasma ... Rather, it would be to avoid pressure drops and maintain good filling. The section of ...
by Retroloc
25/11/04, 17:00
Forum : Water injection in engines: montages and experiments
Subject : Unite us: Great East Region
answers: 18
views: 17147

A note: if the conference is moderated by a certain Realdon: FLY! You will only waste your time and money! Boycott and denounce this scammer! Otherwise if the conference is free or at an affordable rate and it is NOT hosted by this gentleman! no problem ! Go for it ! I've had ...
by Retroloc
25/11/04, 16:42
Forum : Water injection in engines: montages and experiments
Subject : Pantone engine in Southwest Region
answers: 53
views: 75023

I went back to roughly 1850 in a chemistry book and found similar assemblies, unbelievable no !! Personally, whether it is old or recent, it will not change the questions of whether today I have within my reach the means of an achievement. Where are you adapting ...
by Retroloc
25/11/04, 16:37
Forum : Water injection in engines: montages and experiments
Subject : Pantone fixtures in the Centre Region
answers: 38
views: 47088

. Ulysse19, 37 years old, Engineer by training. I am near Tulle in Corrèze. I have been interested in the Pantone project for only 1 month. And I intend to verify the principle on a desiel engine. I am ready to share the experience. And why not participate in the creation of an association ...
by Retroloc
25/11/04, 16:31
Forum : Water injection in engines: montages and experiments
Subject : Pantone fixtures in the Centre Region
answers: 38
views: 47088

Hello, For my part I am in Nevers. I learned about PMC and made a first mower in 2001. The expense and pollution of a mower is of little interest compared to that of a car or a domestic boiler. Also I am progressing towards a road adaptation. Needs...

Go Advanced search