Hello,
Owner of a Pellematic since December 2009, I read a lot of posts on this forum and I learned a lot about the functioning of the boiler, the regulation, certain settings, etc ...
However, wishing to further improve my settings, I realize that certain functions mentioned in the forum, but also on the okofen doc that I have is not accessible.
I also have an interior sensor (white box with wheel and 4-position "cursor") for which, having no instructions, I took a long time to understand the operation. But now, there it is!
I therefore launch this subject to discuss the different functions of these regul / probe.
I have questions first: I can't reach the following functions which appear on my doc:
- change of the max flow temperature (indicated as accessible in "heating circuit / continued / setting")
- DHW priority (accessible via "DHW / suite / setting"): "on" position inaccessible
Are these functions accessible only by access code? If yes, do you know this code?
Pellematic ÖkoFEN: running white control
I do not know the "white" regulation (I have gray).
In some cases, some "options" depend on upstream settings. Kind (this is a theoretical example - since I don't have the doc): setting the maximum temperature etc ... possible if a motorized 3-way valve is installed (which corresponds to a setting made before). .
Well, that is not a good answer, but at least one avenue of research!
But on the 70 page thread relating to the functioning of the Okofen, there are owners of the white regul ...
In some cases, some "options" depend on upstream settings. Kind (this is a theoretical example - since I don't have the doc): setting the maximum temperature etc ... possible if a motorized 3-way valve is installed (which corresponds to a setting made before). .
Well, that is not a good answer, but at least one avenue of research!
But on the 70 page thread relating to the functioning of the Okofen, there are owners of the white regul ...
0 x
Hi,
I have white spur.
Yes, you need the code to modify these 2 parameters.
See this document.
https://www.econologie.info/share/partag ... cAbgjQ.pdf
jc
I have white spur.
Yes, you need the code to modify these 2 parameters.
See this document.
https://www.econologie.info/share/partag ... cAbgjQ.pdf
jc
0 x
Continually trying we finally succeed. So more it fails, the more likely it is that it works.
Hello,
I managed to enter the settings inaccessible at the start by entering the code as mentioned in the message from manet42, ie:
-the first 2 digits are those of the current hour
- and the next two are those of the day
for example 12:42 p.m. on 28 -03-10
you must enter the code 1228
Other parameters than those I mentioned in my 1st message are accessible.
In particular, I was able to access the "legionella protection" function of the ECS. This function, when activated, allows you to heat domestic hot water to 60 ° C once a week. Therefore, when it is activated, you can set the maximum DHW temperature to 50 ° C, which is often quite sufficient and which allows savings.
I managed to enter the settings inaccessible at the start by entering the code as mentioned in the message from manet42, ie:
-the first 2 digits are those of the current hour
- and the next two are those of the day
for example 12:42 p.m. on 28 -03-10
you must enter the code 1228
Other parameters than those I mentioned in my 1st message are accessible.
In particular, I was able to access the "legionella protection" function of the ECS. This function, when activated, allows you to heat domestic hot water to 60 ° C once a week. Therefore, when it is activated, you can set the maximum DHW temperature to 50 ° C, which is often quite sufficient and which allows savings.
0 x
Well done..
If necessary, the complete manual:
https://www.econologie.info/share/partag ... VL3lFK.pdf
JC
If necessary, the complete manual:
https://www.econologie.info/share/partag ... VL3lFK.pdf
JC
0 x
Continually trying we finally succeed. So more it fails, the more likely it is that it works.
-
- Similar topics
- Replies
- views
- Last message
-
- 1 Replies
- 1117 views
-
Last message by Pilpoill
View the latest post
12/02/24, 22:04A subject posted in the forum : Heating, insulation, ventilation, VMC, cooling ...
-
- 10 Replies
- 3173 views
-
Last message by Clemclem
View the latest post
26/12/23, 11:05A subject posted in the forum : Heating, insulation, ventilation, VMC, cooling ...
-
- 14 Replies
- 3005 views
-
Last message by Peso
View the latest post
25/11/23, 15:27A subject posted in the forum : Heating, insulation, ventilation, VMC, cooling ...
-
- 3 Replies
- 7068 views
-
Last message by GwenJ
View the latest post
23/03/24, 14:40A subject posted in the forum : Heating, insulation, ventilation, VMC, cooling ...
-
- 2 Replies
- 1874 views
-
Last message by Peso
View the latest post
26/02/23, 14:42A subject posted in the forum : Heating, insulation, ventilation, VMC, cooling ...
Back to "Heating, insulation, ventilation, VMC, cooling ..."
Who is online ?
Users browsing this forum : Google Adsense [Bot] and 333 guests