Are you sure ?
It is however to you that he is addressing.
Renault R19 D engine with pantone
-
- I learn econologic
- posts: 16
- Registration: 19/12/05, 15:46
- Location: Quincy (expensive)
r19 d
ok ok
Mea culpa!
has exeed:
I cheated mister
I would do more
for your pump problem, you'd better change the probe, it's done very well, and return to your original setting (stretched to the cold stopper, and relaxed as soon as it's hot)
thanks again.
rabbit:
thank you if you can have the diagram.
ps: there is snow here (bourges) or rather QUINCY (some connoisseurs? let's see!)
two clues: it's in September ......
in Quincy we are not racite, no, but we much prefer the "white"
Mea culpa!
has exeed:
I cheated mister
I would do more
for your pump problem, you'd better change the probe, it's done very well, and return to your original setting (stretched to the cold stopper, and relaxed as soon as it's hot)
thanks again.
rabbit:
thank you if you can have the diagram.
ps: there is snow here (bourges) or rather QUINCY (some connoisseurs? let's see!)
two clues: it's in September ......
in Quincy we are not racite, no, but we much prefer the "white"
0 x
-
- I learn econologic
- posts: 16
- Registration: 19/12/05, 15:46
- Location: Quincy (expensive)
r19d alternator !!
hello to all those who gave me tips, but hello that's it I repaired
I'm going to tell you what it was, because I think many of us would have done like "dried"!
in fact it is the demper which is "pulverized" that is to say that the pulley mounted so silent block on the hub is detached from the hub, and it had to make noise for me to see the problem!
following a message here, (I don't know who), I had looked at this pulley, but at that time, the rubber was still in place, and it made no noise (normal!).
well it's back to school tomorrow,: cry: and i seriously attack the pantone.
thank you all again and see you soon for news from the front.
I'm going to tell you what it was, because I think many of us would have done like "dried"!
in fact it is the demper which is "pulverized" that is to say that the pulley mounted so silent block on the hub is detached from the hub, and it had to make noise for me to see the problem!
following a message here, (I don't know who), I had looked at this pulley, but at that time, the rubber was still in place, and it made no noise (normal!).
well it's back to school tomorrow,: cry: and i seriously attack the pantone.
thank you all again and see you soon for news from the front.
0 x
-
- I learn econologic
- posts: 16
- Registration: 19/12/05, 15:46
- Location: Quincy (expensive)
pantone r19 D
Hello
no no it was not for the breakdown
the proof, i have just seen my workshop colleagues and i am fully into it.
I'm trying to bend a stainless steel tub for the reactor.
see you soon
ps: my colleagues are very skeptical I will try to impress them
thanks again
no no it was not for the breakdown
the proof, i have just seen my workshop colleagues and i am fully into it.
I'm trying to bend a stainless steel tub for the reactor.
see you soon
ps: my colleagues are very skeptical I will try to impress them
thanks again
0 x
-
- I discovered econologic
- posts: 1
- Registration: 10/06/08, 14:17
- Location: Villefranche sur Saône / Bourg-en-Bresse
Water mower
Hello friends, this is Lula the little news. Not at all handyman, I am looking for a low-cost water mower for my garden. Thank you for making me a proposal on action8bio [at] gmail.com
0 x
Re: Water mower
Hello little news
I'm not sure you'll find this in stock on the corner of a shelf. Read a bit about the different post pantone, in all cases you have to fight to develop / tinker with something that works.
But if you want to get started, welcome to the club.
Lula wrote:Hello friends, this is Lula the little news. Not at all handyman, I am looking for a low-cost water mower for my garden. Thank you for making me a proposal on action8bio [at] gmail.com
I'm not sure you'll find this in stock on the corner of a shelf. Read a bit about the different post pantone, in all cases you have to fight to develop / tinker with something that works.
But if you want to get started, welcome to the club.
0 x
Reason is the madness of the strongest. The reason for the less strong it is madness.
[Eugène Ionesco]
http://www.editions-harmattan.fr/index. ... te&no=4132
[Eugène Ionesco]
http://www.editions-harmattan.fr/index. ... te&no=4132
-
- Similar topics
- Replies
- views
- Last message
-
- 31 Replies
- 38194 views
-
Last message by brahimour
View the latest post
31/01/14, 01:01A subject posted in the forum : Water injection in engines: montages and experiments
-
- 4 Replies
- 11640 views
-
Last message by Flytox
View the latest post
29/10/13, 22:52A subject posted in the forum : Water injection in engines: montages and experiments
-
- 13 Replies
- 26287 views
-
Last message by Flytox
View the latest post
08/03/12, 18:53A subject posted in the forum : Water injection in engines: montages and experiments
-
- 48 Replies
- 78958 views
-
Last message by ciwil66
View the latest post
17/07/12, 00:35A subject posted in the forum : Water injection in engines: montages and experiments
-
- 5 Replies
- 6008 views
-
Last message by Other
View the latest post
16/04/10, 17:16A subject posted in the forum : Water injection in engines: montages and experiments
Back to "Water injection in the engines: the assembly and experimentation"
Who is online ?
Users browsing this forum : No registered users and 163 guests