Pantone Toyota Lite ace of diesel 1994
You make us the diagram of the assembly and the photos !?
0 x
Reason is the madness of the strongest. The reason for the less strong it is madness.
[Eugène Ionesco]
http://www.editions-harmattan.fr/index. ... te&no=4132
[Eugène Ionesco]
http://www.editions-harmattan.fr/index. ... te&no=4132
rod length?
for the length of the rod, I read this text several times:
But that necessarily implies that the rod must be reduced in any case ???
One of the most unusual features: cylinder when you prowl the rod you have to operate the device in a North orientation for 30 minutes, only for the first
Once this is done properly, you can remove the rod and the distance between North and South on the rod will indicate the suitable length that your rod should have had for the chosen fuel and for your type of aircraft.
But that necessarily implies that the rod must be reduced in any case ???
0 x
Re: length of the rod?
Bubul wrote:for the length of the rod, I read this text several times:One of the most unusual features: cylinder when you prowl the rod you have to operate the device in a North orientation for 30 minutes, only for the first
Once this is done properly, you can remove the rod and the distance between North and South on the rod will indicate the suitable length that your rod should have had for the chosen fuel and for your type of aircraft.
These words are nonsense probably from Mr. Pantone himself. It's rubbish in its purest form. Many people operate their Pantone with a stainless steel rod .... non-magnetic, non-retentive and never pay attention to the slightest orientation. There may be some magnetic phenomena during operation but they do not depend on the orientation of the rod on the planet at the start.
0 x
Reason is the madness of the strongest. The reason for the less strong it is madness.
[Eugène Ionesco]
http://www.editions-harmattan.fr/index. ... te&no=4132
[Eugène Ionesco]
http://www.editions-harmattan.fr/index. ... te&no=4132
Re: length of the rod?
These words are nonsense probably from Mr. Pantone himself. It's rubbish in its purest form
Thank you for the info, its done less to do!
0 x
Hello
It is a small drawback to pass water through a cold reactor but it does not last long so make it simple, once the reactor is warm it stabilizes,
So made simple without solenoid valve.
It's all the little accessories and gadgets that are lacking around the reactor that make that give problems, so make it simple, once the system is running, go to improvement to make it more easy to operate.
Andre
Bubul wrote:do you need a (homemade) solenoid valve between the bubbler and the reactor which would prevent water vapor from passing during startup before the reactor is hot?
It is a small drawback to pass water through a cold reactor but it does not last long so make it simple, once the reactor is warm it stabilizes,
So made simple without solenoid valve.
It's all the little accessories and gadgets that are lacking around the reactor that make that give problems, so make it simple, once the system is running, go to improvement to make it more easy to operate.
Andre
0 x
Andre wrote:HelloBubul wrote:do you need a (homemade) solenoid valve between the bubbler and the reactor which would prevent water vapor from passing during startup before the reactor is hot?
It is a small drawback to pass water through a cold reactor but it does not last long so make it simple, once the reactor is warm it stabilizes,
So made simple without solenoid valve.
It's all the little accessories and gadgets that are lacking around the reactor that make that give problems, so make it simple, once the system is running, go to improvement to make it more easy to operate.
Andre
Ok, I'll start simple and then make changes.
thank you André
0 x
So made simple without solenoid valve.
+1 André. I tried that, a complicated thing that ate me a lot of development time .... for not much ...
0 x
Reason is the madness of the strongest. The reason for the less strong it is madness.
[Eugène Ionesco]
http://www.editions-harmattan.fr/index. ... te&no=4132
[Eugène Ionesco]
http://www.editions-harmattan.fr/index. ... te&no=4132
T ° air blower?
The temperature of the air entering the bubbler must be at the temperature of the water (90 °) or warmer?
For the moment I have made an air heating system with a copper coil placed in the water of the bubbler. I don't know if it's better than heating the air with a coil around the exhaust pipe ...
For the moment I have made an air heating system with a copper coil placed in the water of the bubbler. I don't know if it's better than heating the air with a coil around the exhaust pipe ...
0 x
-
- Similar topics
- Replies
- views
- Last message
-
- 6 Replies
- 6430 views
-
Last message by bleusideral
View the latest post
29/04/18, 19:49A subject posted in the forum : Water injection in engines: montages and experiments
-
- 27 Replies
- 29590 views
-
Last message by chatelot16
View the latest post
31/07/16, 11:00A subject posted in the forum : Water injection in engines: montages and experiments
-
- 1 Replies
- 5575 views
-
Last message by Flytox
View the latest post
01/12/15, 22:07A subject posted in the forum : Water injection in engines: montages and experiments
-
- 41 Replies
- 53869 views
-
Last message by Flytox
View the latest post
28/02/14, 18:43A subject posted in the forum : Water injection in engines: montages and experiments
-
- 21 Replies
- 32559 views
-
Last message by dede2002
View the latest post
17/02/14, 21:05A subject posted in the forum : Water injection in engines: montages and experiments
Back to "Water injection in the engines: the assembly and experimentation"
Who is online ?
Users browsing this forum : No registered users and 163 guests