Pantone for Peugeot 406 cut
Jean Valjean wrote:hello, I redo my account pantone, I wanted to know if it is necessary to increase the section of the pipe at the reactor?
Which section are you talking about? You can not make a diagram please?
0 x
Reason is the madness of the strongest. The reason for the less strong it is madness.
[Eugène Ionesco]
http://www.editions-harmattan.fr/index. ... te&no=4132
[Eugène Ionesco]
http://www.editions-harmattan.fr/index. ... te&no=4132
-
- I learn econologic
- posts: 26
- Registration: 16/05/10, 00:01
- Location: Bordeaux
-
- I learn econologic
- posts: 26
- Registration: 16/05/10, 00:01
- Location: Bordeaux
Jean Valjean wrote:the party surround the picture, now is the 60,3 diameter ext ext spend a 76? because the reactor not bad mouth the passage of gas
By changing to 76 mm, this allows you to recover the original passage section of the exhaust I suppose. It should not be larger than the origin in passage section, it drops the temperature for the reactor and in any case will not improve the agreement of the pot.
From what I could see on the net, for the Lamda probe, those who tamper with its information are most often more motivated by the search for power by "decalyzing" (or the economy of replacing the catalyst) rather than by seeking less pollution. André, you who use this lambda information, what do you do with it?
0 x
Reason is the madness of the strongest. The reason for the less strong it is madness.
[Eugène Ionesco]
http://www.editions-harmattan.fr/index. ... te&no=4132
[Eugène Ionesco]
http://www.editions-harmattan.fr/index. ... te&no=4132
-
- I learn econologic
- posts: 26
- Registration: 16/05/10, 00:01
- Location: Bordeaux
Simple and effective and in stainless steel!
Have you welded the 2 ends (threaded rods) of the rod into the inlet and outlet elbows? There can be a big difference in temperature and therefore in expansion, between the reactor shell and the rod, possibly this can cause a lot of effort and cause a weld to crack. In my case, I only welded one end of the casing and the (removable) rod can move with a "soft" joint.
If you use non-demineralized water, (it's more effective according to some testers), limestone and other minerals end up clinging in the reactor and half-clogging it . It should therefore be possible to clean it in one way or another (removable rod, acid passage possible etc ...) after X km or month of use.
A+
Have you welded the 2 ends (threaded rods) of the rod into the inlet and outlet elbows? There can be a big difference in temperature and therefore in expansion, between the reactor shell and the rod, possibly this can cause a lot of effort and cause a weld to crack. In my case, I only welded one end of the casing and the (removable) rod can move with a "soft" joint.
If you use non-demineralized water, (it's more effective according to some testers), limestone and other minerals end up clinging in the reactor and half-clogging it . It should therefore be possible to clean it in one way or another (removable rod, acid passage possible etc ...) after X km or month of use.
A+
Last edited by Flytox the 20 / 09 / 10, 18: 49, 1 edited once.
0 x
Reason is the madness of the strongest. The reason for the less strong it is madness.
[Eugène Ionesco]
http://www.editions-harmattan.fr/index. ... te&no=4132
[Eugène Ionesco]
http://www.editions-harmattan.fr/index. ... te&no=4132
-
- I learn econologic
- posts: 26
- Registration: 16/05/10, 00:01
- Location: Bordeaux
-
- I learn econologic
- posts: 26
- Registration: 16/05/10, 00:01
- Location: Bordeaux
Hello jeanvaljean
You do not risk much, noise or a small leak at most
For acid, stainless steel is good but the scrap surrounding the pot is not great. Above all, for the acid to go clean everywhere, it is necessary to handle the end of pipe, if it is 2 or 3 m long it is much less convenient ...
Jean Valjean wrote:I have quoted weld 2 because of the old mount the rod had to take the game and put a vibrate making a noise casserol.si ca ca casse risk what? to clean it if I put the AC acid should do ?
You do not risk much, noise or a small leak at most
For acid, stainless steel is good but the scrap surrounding the pot is not great. Above all, for the acid to go clean everywhere, it is necessary to handle the end of pipe, if it is 2 or 3 m long it is much less convenient ...
Last edited by Flytox the 22 / 09 / 10, 21: 52, 1 edited once.
0 x
Reason is the madness of the strongest. The reason for the less strong it is madness.
[Eugène Ionesco]
http://www.editions-harmattan.fr/index. ... te&no=4132
[Eugène Ionesco]
http://www.editions-harmattan.fr/index. ... te&no=4132
-
- Similar topics
- Replies
- views
- Last message
-
- 6 Replies
- 7380 views
-
Last message by bleusideral
View the latest post
29/04/18, 19:49A subject posted in the forum : Water injection in engines: montages and experiments
-
- 27 Replies
- 32982 views
-
Last message by chatelot16
View the latest post
31/07/16, 11:00A subject posted in the forum : Water injection in engines: montages and experiments
-
- 1 Replies
- 6546 views
-
Last message by Flytox
View the latest post
01/12/15, 22:07A subject posted in the forum : Water injection in engines: montages and experiments
-
- 41 Replies
- 57879 views
-
Last message by Flytox
View the latest post
28/02/14, 18:43A subject posted in the forum : Water injection in engines: montages and experiments
-
- 21 Replies
- 34937 views
-
Last message by dede2002
View the latest post
17/02/14, 21:05A subject posted in the forum : Water injection in engines: montages and experiments
Back to "Water injection in the engines: the assembly and experimentation"
Who is online ?
Users browsing this forum : No registered users and 180 guests