Water injection without pantone Vs pantone
@lau
5l / 100 of water, it's not disgusting! lol
Yep, already installed a kit N2O ... it works very hard! it kills the engine very strong too! Bah, overall I'm not a fan of this kind of article ... already, because it is allowed in almost no discipline ... And then after, because it is faaaible as a method, it has no class ... Anyone can double his power in a short time by putting a kit Our ... cons multiply power by 2 without kit Our, it's class! and then the worst is that after doing this, you still have the opportunity to put a Nos for special races like 400DA ...
5l / 100 of water, it's not disgusting! lol
Yep, already installed a kit N2O ... it works very hard! it kills the engine very strong too! Bah, overall I'm not a fan of this kind of article ... already, because it is allowed in almost no discipline ... And then after, because it is faaaible as a method, it has no class ... Anyone can double his power in a short time by putting a kit Our ... cons multiply power by 2 without kit Our, it's class! and then the worst is that after doing this, you still have the opportunity to put a Nos for special races like 400DA ...
0 x
Not bad the needle system, the fog is rather clean.
But since you use the pressure of the turbo, you are forced to inject the water before the turbo, otherwise you have no pressure difference between the pipe, and your pulsed air ...
It would take a way to get a small airflow at a higher pressure ...
To do that, I had experimented with something:
some small-displacement model engines operate with a pressurized CO2 cartridge and a check valve. By reversing the direction of the valve and driving the crankshaft via a small electric motor, we have a small air compressor ... it works pretty well ...
I should be able to find plans if it interferes with someone ...
Paired with the needle system of binbins4, it could make a cheap injection of water ...
But since you use the pressure of the turbo, you are forced to inject the water before the turbo, otherwise you have no pressure difference between the pipe, and your pulsed air ...
It would take a way to get a small airflow at a higher pressure ...
To do that, I had experimented with something:
some small-displacement model engines operate with a pressurized CO2 cartridge and a check valve. By reversing the direction of the valve and driving the crankshaft via a small electric motor, we have a small air compressor ... it works pretty well ...
I should be able to find plans if it interferes with someone ...
Paired with the needle system of binbins4, it could make a cheap injection of water ...
0 x
Hello Wroom 143
it's a question I asked myself about doping with water
and I think it would be best to send what comes out of the reactor
after the turbo. Everyone enters before the turbo for reasons of simplicity, but I do not like, to pass it, by the turbo aluminum wheel the speed at the end of the blade must be close to the speed of sound, my view Aircraft propeller repair experience, at each takeoff on water, on seaplanes.
the drops of water rolled the duralumin helix, enough that the drops penetrates 3mm into the metal on the leading edge.
So if anything the reactor lets pass finne drop of water must be damaging, In addition to what comes out of the panton in this mill says nothing good ..
Now to go back from the turbo it is necessary that the reactor is pressurized at the entrance, something that I tried with the pressure of the turbo, it is necessary by a suitable form that the exit of the reactor that which enters the collector is in relative depression to have a circulation in the reactor, it is feasible, the only thing before undertaking this modification is to evaluate the advantages.
Andre
it's a question I asked myself about doping with water
and I think it would be best to send what comes out of the reactor
after the turbo. Everyone enters before the turbo for reasons of simplicity, but I do not like, to pass it, by the turbo aluminum wheel the speed at the end of the blade must be close to the speed of sound, my view Aircraft propeller repair experience, at each takeoff on water, on seaplanes.
the drops of water rolled the duralumin helix, enough that the drops penetrates 3mm into the metal on the leading edge.
So if anything the reactor lets pass finne drop of water must be damaging, In addition to what comes out of the panton in this mill says nothing good ..
Now to go back from the turbo it is necessary that the reactor is pressurized at the entrance, something that I tried with the pressure of the turbo, it is necessary by a suitable form that the exit of the reactor that which enters the collector is in relative depression to have a circulation in the reactor, it is feasible, the only thing before undertaking this modification is to evaluate the advantages.
Andre
0 x
- binbins4
- I understand econologic
- posts: 165
- Registration: 27/12/04, 09:46
- Location: Geneva, Switzerland)
after some static test for on a fiat ducato 2.8 td id (camping car) I will use the pump of the cell which is at 1.8 bar to push in pressure turbo, the injector that WROOUM board grilled, I have it in 12 Moreover, he is too busy and not sure how to beat it, should he have a sequence with him?
I arrived spraying with a perfume duster approx 1.1lt on time the quantity should fuck in turbo pressure, I pulverise only if the turbo pressure exceeds0,2 bar with a pressure switch of washing machine.
I arrived spraying with a perfume duster approx 1.1lt on time the quantity should fuck in turbo pressure, I pulverise only if the turbo pressure exceeds0,2 bar with a pressure switch of washing machine.
0 x
Hello Binbins4
In general the injectors are not fed constantly, in DC
the coils do not support, it is necessary to send implants, with a 555 the flow is done by the duration of time (one versus the off)
Do not mix injector and electric valve.
If you do not put the 555 well I would indicate a montage with a relay that vibrates, easy to do with some piece of wire ..
When you send DC power in a coil it takes a (some time) to mount the amperage, pulsating the current amperage of the coil is low, it is as if we were feeding AC power.
Since you are in the water just injecting water, could you give some results, like clean candles or engine oil? engine behavior, water consumption little or much? consumption or power if there is a difference?
As I did not finish the assembly of a reactor on a gasoline engine old generation, I asked the question if it was worth doing tests just with the water in the admission?
Andre
In general the injectors are not fed constantly, in DC
the coils do not support, it is necessary to send implants, with a 555 the flow is done by the duration of time (one versus the off)
Do not mix injector and electric valve.
If you do not put the 555 well I would indicate a montage with a relay that vibrates, easy to do with some piece of wire ..
When you send DC power in a coil it takes a (some time) to mount the amperage, pulsating the current amperage of the coil is low, it is as if we were feeding AC power.
Since you are in the water just injecting water, could you give some results, like clean candles or engine oil? engine behavior, water consumption little or much? consumption or power if there is a difference?
As I did not finish the assembly of a reactor on a gasoline engine old generation, I asked the question if it was worth doing tests just with the water in the admission?
Andre
0 x
- binbins4
- I understand econologic
- posts: 165
- Registration: 27/12/04, 09:46
- Location: Geneva, Switzerland)
Hi Andre, your scheme interests me, me and the electronics
I will prepare two montages to go on holiday with a venturi in turbo pressure with the tank also in pressure and a check valve, a filling when the pressure decreases.
the other as on my previous post.
I wonder if it happens to find more pressure in the turbo snail that could be useful.
the ducato fiat is the only one that is not equipped pantone is probably a mistake, because the only one that is in anyway it does not cost me a lot of fuel 4000km with a full of gasoil remains hvr (R for recup)
I will prepare two montages to go on holiday with a venturi in turbo pressure with the tank also in pressure and a check valve, a filling when the pressure decreases.
the other as on my previous post.
I wonder if it happens to find more pressure in the turbo snail that could be useful.
the ducato fiat is the only one that is not equipped pantone is probably a mistake, because the only one that is in anyway it does not cost me a lot of fuel 4000km with a full of gasoil remains hvr (R for recup)
0 x
Hello,
For fuel injectors auto coil is a resistance of 14,5 homs
but that does not mean anything given the size of the thread of the bonbine I doubt that to pass in continuous 500 milliampere that the thread resites.
it's more like ON OFF pulse and not too long ON
It remains to be seen if the values of the European material are the same as those of GM.
The simple assembly is a relay to which its own contact runs its coil all in series with the injector, it makes a vibrator, which oscillates according to the relay, but it is not modulable, it just allows the injector to survive with pulsating current.
The best is to make a montage with an 555, Ask Michel du forum or guidi I think they have more experience in these montages than me, they sell small support and some components to make these small montages and you can adjust the pulsations with a small poteniometer.
Andre
For fuel injectors auto coil is a resistance of 14,5 homs
but that does not mean anything given the size of the thread of the bonbine I doubt that to pass in continuous 500 milliampere that the thread resites.
it's more like ON OFF pulse and not too long ON
It remains to be seen if the values of the European material are the same as those of GM.
The simple assembly is a relay to which its own contact runs its coil all in series with the injector, it makes a vibrator, which oscillates according to the relay, but it is not modulable, it just allows the injector to survive with pulsating current.
The best is to make a montage with an 555, Ask Michel du forum or guidi I think they have more experience in these montages than me, they sell small support and some components to make these small montages and you can adjust the pulsations with a small poteniometer.
Andre
0 x
-
- Similar topics
- Replies
- views
- Last message
-
- 11 Replies
- 32989 views
-
Last message by Christophe
View the latest post
04/09/16, 19:12A subject posted in the forum : Water injection in heat engines: information and explanations
-
- 3 Replies
- 9271 views
-
Last message by Christophe
View the latest post
28/06/16, 23:24A subject posted in the forum : Water injection in heat engines: information and explanations
-
- 25 Replies
- 23368 views
-
Last message by Christophe
View the latest post
12/03/16, 03:18A subject posted in the forum : Water injection in heat engines: information and explanations
-
- 18 Replies
- 21057 views
-
Last message by Christophe
View the latest post
07/10/17, 18:56A subject posted in the forum : Water injection in heat engines: information and explanations
-
- 35 Replies
- 53340 views
-
Last message by Macro
View the latest post
30/09/15, 08:34A subject posted in the forum : Water injection in heat engines: information and explanations
Go back to "Water injection in heat engines: information and explanations"
Who is online ?
Users browsing this forum : No registered users and 141 guests