thank you for this post that I follow too.
I have had a b-max burner since June of this year.
I cannot speak of the differences between the b-max and the sun.
what i know is that the b-max has a diameter of being in the boiler of 110mm, which allowed me to install it without making any modification to the door.
this is a significant point.
then for the settings they are quite delicate.
I find my consumption of pellet to compare with fuel a little too important.
I will try to increase the ventilation.
in fact i was trying to make adjustments with a very low cost clearance, but it may not be necessarily the best thing to do.
and I also tried to reduce the temperature of the smoke, but finally between 200 and 250, if it's not bad I will try in these parameters.
I know that at that time I consumed about 10l of fuel / day and that today I am at a little more than 25Kilo of pellet / day.
the overall yield is therefore poorer.
it's not easy to settle these little beasts there.
How to choose a pellet burner?
-
- I understand econologic
- posts: 57
- Registration: 03/01/11, 09:03
- Location: isere-Savoie
- x 2
Who has feedback on the Ulma 2000TC?
I have read that the Ulma 2000TC pellet burner has an efficiency of 97%.
The Okke France site is closed, is there a relationship between Okke and Ulma?
The Okke France site is closed, is there a relationship between Okke and Ulma?
0 x
- chatelot16
- Econologue expert
- posts: 6960
- Registration: 11/11/07, 17:33
- Location: Angouleme
- x 264
you don't have to break your head looking for problems or there are none
to adjust the air flow, if there is too much air it loses a little more heat by the flow in the chimney but it is not very serious
if there is not enough air flow of the combustible gas leaves through the chimney: it makes a catastrophic loss of energy, but it is visible: it quickly fouls the boiler, it makes a red flame which fills all Boiler
sufficient air flow is therefore necessary so that the burner flame does not fill the boiler, and the boiler does not clog up too quickly
as the combustion conditions are variable and the excess air is less serious than the lack, it is necessary to put rather too much air than not enough: it is ultimately the same principle as for the adjustment of the oil burner
to adjust the air flow, if there is too much air it loses a little more heat by the flow in the chimney but it is not very serious
if there is not enough air flow of the combustible gas leaves through the chimney: it makes a catastrophic loss of energy, but it is visible: it quickly fouls the boiler, it makes a red flame which fills all Boiler
sufficient air flow is therefore necessary so that the burner flame does not fill the boiler, and the boiler does not clog up too quickly
as the combustion conditions are variable and the excess air is less serious than the lack, it is necessary to put rather too much air than not enough: it is ultimately the same principle as for the adjustment of the oil burner
0 x
-
- Similar topics
- Replies
- views
- Last message
-
- 3 Replies
- 6311 views
-
Last message by Christophe
View the latest post
29/11/18, 18:50A subject posted in the forum : Hydraulic, wind, geothermal, marine energy, biogas ...
-
- 8 Replies
- 6675 views
-
Last message by peter
View the latest post
04/11/23, 12:12A subject posted in the forum : Hydraulic, wind, geothermal, marine energy, biogas ...
-
- 54 Replies
- 35178 views
-
Last message by Remundo
View the latest post
26/03/14, 14:29A subject posted in the forum : Hydraulic, wind, geothermal, marine energy, biogas ...
-
- 3 Replies
- 6470 views
-
Last message by coccigro
View the latest post
09/03/13, 09:03A subject posted in the forum : Hydraulic, wind, geothermal, marine energy, biogas ...
-
- 123 Replies
- 83716 views
-
Last message by Obamot
View the latest post
22/05/22, 15:12A subject posted in the forum : Hydraulic, wind, geothermal, marine energy, biogas ...
Back to "hydraulic, wind, geothermal, marine energy, biogas ..."
Who is online ?
Users browsing this forum : No registered users and 237 guests