polycombustible steam boiler
-
- I posted 500 messages!
- posts: 519
- Registration: 02/12/08, 20:44
- x 12
-
- I posted 500 messages!
- posts: 519
- Registration: 02/12/08, 20:44
- x 12
Hello ! Happy New Year to all the curious ...
Good yesterday I did some manipulations with my little pot of "vap poly comb"
I made some measurements and I made a plan that I attach to you. I modified the air holes as shown on the plan, (the 3 bottom holes are raised by 1cm.) All the details are on the plan.I measured the fuel consumption (gas oil + sunflower oil) with A kitchen scale gram close The measurement starts with all in steady heat regime I wanted to note the fuel consumption, the average power consumed by the compressor, the temperature of the pot.
Here are the measurements (hour, tank weight in gr, whether or not the air compressor, 0,35 Bar pressure (229v, 6,85a, cos phi = 08, Absorbed = 1255w):
15h38mn00s 331g comp = 0 (start of measurements.)
15 41 00 321g c = 0
15 41 45 316g c = 1
15 43 00 311g c = 1
15 43 40 306g c = 0
15 45 00 303g c = 0
15 46 00 299g c = 0
15 46 10 298g c = 1
15 47 00 294g c = 1
15 48 10 ........ c = 0
15 49 00 285g c = 0
15 50 00 281g c = 0
15 50 40 278g c = 1
15 52 45 268g c = 0
I conclude that in 885 seconds I consumed 63g fuel either (63: 885) x3600 = 256g per hour or fueled power consumption (10kwh / liters x 0,256) = 2560 watts(+ -)
Power consumed by the compressor: it worked 360s on 885s so 40% of the time is on average 1255w x 0.4 or 502w.
During this test I think I had too much air injected (the flames came out a little of the pot) hence the consumption of the compressor ...
I also think that holes are too close to the top of the pot ... These parameters are very important to optimize the operation. I will join some photos and video very soon ...
a+
DanielJ
Good yesterday I did some manipulations with my little pot of "vap poly comb"
I made some measurements and I made a plan that I attach to you. I modified the air holes as shown on the plan, (the 3 bottom holes are raised by 1cm.) All the details are on the plan.I measured the fuel consumption (gas oil + sunflower oil) with A kitchen scale gram close The measurement starts with all in steady heat regime I wanted to note the fuel consumption, the average power consumed by the compressor, the temperature of the pot.
Here are the measurements (hour, tank weight in gr, whether or not the air compressor, 0,35 Bar pressure (229v, 6,85a, cos phi = 08, Absorbed = 1255w):
15h38mn00s 331g comp = 0 (start of measurements.)
15 41 00 321g c = 0
15 41 45 316g c = 1
15 43 00 311g c = 1
15 43 40 306g c = 0
15 45 00 303g c = 0
15 46 00 299g c = 0
15 46 10 298g c = 1
15 47 00 294g c = 1
15 48 10 ........ c = 0
15 49 00 285g c = 0
15 50 00 281g c = 0
15 50 40 278g c = 1
15 52 45 268g c = 0
I conclude that in 885 seconds I consumed 63g fuel either (63: 885) x3600 = 256g per hour or fueled power consumption (10kwh / liters x 0,256) = 2560 watts(+ -)
Power consumed by the compressor: it worked 360s on 885s so 40% of the time is on average 1255w x 0.4 or 502w.
During this test I think I had too much air injected (the flames came out a little of the pot) hence the consumption of the compressor ...
I also think that holes are too close to the top of the pot ... These parameters are very important to optimize the operation. I will join some photos and video very soon ...
a+
DanielJ
0 x
vap poly comb (small pot)
I promised photos and videos of the manip, here they are:
Note that I have a fire extinguisher not far! And you ?
a + friends ...
Note that I have a fire extinguisher not far! And you ?
a + friends ...
0 x
steam burner poly comb (small pot)
videos:
http://www.youtube.com/watch?v=Ai3oTEgAP5U
http://www.youtube.com/watch?v=iksuyhdCFpE
http://www.youtube.com/watch?v=c6vbSqXeask
Measured, 799 ° C against the outside of the pot, about 1000 ° C at the exit of the flames, although my thermocouple thermometer type k can go up to 1300 ° C, I did not want to go in the middle of the flame to not grill it ...
a+
danielj
http://www.youtube.com/watch?v=Ai3oTEgAP5U
http://www.youtube.com/watch?v=iksuyhdCFpE
http://www.youtube.com/watch?v=c6vbSqXeask
Measured, 799 ° C against the outside of the pot, about 1000 ° C at the exit of the flames, although my thermocouple thermometer type k can go up to 1300 ° C, I did not want to go in the middle of the flame to not grill it ...
a+
danielj
0 x
-
- I posted 500 messages!
- posts: 519
- Registration: 02/12/08, 20:44
- x 12
-
- I posted 500 messages!
- posts: 519
- Registration: 02/12/08, 20:44
- x 12
-
- Similar topics
- Replies
- views
- Last message
-
- 41 Replies
- 6133 views
-
Last message by gek
View the latest post
17/02/23, 12:51A subject posted in the forum : Hydraulic, wind, geothermal, marine energy, biogas ...
-
- 8 Replies
- 3630 views
-
Last message by Sandy
View the latest post
09/11/23, 10:54A subject posted in the forum : Hydraulic, wind, geothermal, marine energy, biogas ...
-
- 1 Replies
- 6507 views
-
Last message by GuyGadeboisTheBack
View the latest post
11/01/22, 18:48A subject posted in the forum : Hydraulic, wind, geothermal, marine energy, biogas ...
-
- 2 Replies
- 9183 views
-
Last message by bducange
View the latest post
26/01/24, 19:10A subject posted in the forum : Hydraulic, wind, geothermal, marine energy, biogas ...
-
- 2 Replies
- 6632 views
-
Last message by Christophe
View the latest post
20/05/14, 11:55A subject posted in the forum : Hydraulic, wind, geothermal, marine energy, biogas ...
Back to "hydraulic, wind, geothermal, marine energy, biogas ..."
Who is online ?
Users browsing this forum : Majestic-12 [Bot] and 257 guests