Responsibility on the forum. Gaudet86 case

[gaudet86]

I'm a big ass

[renaud67]

Hello,
similar technique ... for comparison and maybe that can help
http://www.energeticforum.com/renewable-energy/2255-imhoteps-radiant-oscillator-video.html

[jonule]

[quote = "gaudet86"] I have finished mounting the toroid core, as shown in the diagram ./quote]
what scheme?
can you put back the link of PDF14 stp? with more details?

you are using a PWM from PDF14, ok.
a classic PWM wouldn't work? Why ?
how do you regulate your PWM, "frequency / center selection on the 2 ossilator" what does that mean?

> the PWM we see in the photo with the lamp, where does it come from?

I believe that some of this forum tried to reproduce the PWM from PDF14 but without success ...

> If not, why "free to all reproduction since 2007"?

FACT: hello gaudet and thank you ... a lot to help us relaunch this project, many are reading you

[renaud67]

That must be it :
http://www.panaceauniversity.org/Hydroxy%20Boosters.pdf
where
http://www.panaceauniversity.org/Ravi%20Cell.pdf
otherwise over there ...
http://www.free-energy-info.co.uk/
since the denomination D14 had to change I think (probably chapter10.pdf)
below the last d14 I have
https://www.econologie.com/fichiers/partager/1224144967Md6RAn.pdf

PS: I confirm D14 -> Chapter10.pdf
here: http://www.free-energy-info.co.uk/Chapter10.pdf
in particular page 106 Bob who connects his cell both on the continuous and on the pulsed leaving the torus

[renaud67]

a file containing BOB posts (boyce) that I gleaned below (all on forums public)
not necessarily pleasant to read but full of remarks ... useful

https://www.econologie.com/fichiers/partager/1224169776fEjVNG.pdf

[renaud67]

I copy / paste what I wrote in the improved electrolysis file:
Hello,
in the bob boyce system (I don't want to seem to insist ) there is also a part of conditioning of the plates (101) with "horizontal" and "vertical" "sanding" then a phase (described in chapter10.pdf I think) "electrolyte" to deposit a layer, undoubtedly insulating which must make it possible to give the capacitive character to the cell.
All that to say that there also has something in common with meyer on a conditioning of electrodes. From what I understand, this is the essential point to have the capacitive nature which will allow to have an electrical resonance (moreover bob boyce says that it is indeed an electrical resonance that we seek to not acoustic) and to go up in tension at (X) terminal (S) of the cell.

[jonule]

Hello
I had noted:
"
but most importantly, if you have followed Meyer's work, he runs in stainless steel what I did with my plates:
1 week permanently connected to a battery charger, without electrolyte, fixed on threaded stainless steel rods: a catode & an anode.
afterwards, a whitish film forms on the plates: do not wipe, just clean them with demineralized water.
the water used in the cells is boiled rainwater.
I use stainless steel 904L.
"
would that match?

[jonule]

hello gaudet86, could you please tell us:

> the quality of the stainless steel needed to manufacture the cell meyer? (grade)

> the length of the tubes

> how to condition the tubes?

(big) thank you

[Tagor]

video / show what do pwm a little ..
sorry it's all wrong i haven't had much time / miss battery
and this is my first video ...
http://ca.youtube.com/watch?v=tjQzigSQ074

this video is very interesting!
can we have a diagram of the assembly?
how are the measurements made?

[Tagor]

tu me gnaise tagor ?? vdo very interesting hehh;)
I do a little design of the tanto assembly I will rinse here

I'm not talking about the artistic side but there is finally the concrete
a good manipulation on which we will finally be able to exchange

PS: I have trouble following your French
maybe we can follow better in english?